Concealed-Fastener Wave Profile
AMP Wave 16-4 Metal Wall Panel for Dallas-Fort Worth Buildings
The AMP Wave 16-4 metal wall panel is a concealed-fastener cladding panel with 16 inches of coverage and four rounded waves, each 7/8 inch deep. Architectural Metal Panels roll-forms it to length in Forney and installs it horizontally or vertically on storefronts, offices, schools and modern homes across Dallas-Fort Worth. Architects can request a submittal package; homeowners can start with a free estimate.
- 26+ years in business
- Lifetime warranty
- Free written estimates
What Is the AMP Wave 16-4 Panel?
It is a 16-inch-wide wall panel with four evenly spaced waves, 4 inches on center and 7/8 inch deep, that locks over a hidden fastening leg. No screw heads show on the finished wall. The rounded profile reads as a soft rhythm of shadow lines rather than the sharp ridges of a corrugated barn wall.
The figures below come from the AMP profile data. Values marked “typically” are the industry-standard figures for this class of panel; your spec sheet confirms them for the gauge and material you order.
| Specification | AMP Wave 16-4 |
|---|---|
| Net coverage | 16 inches per panel |
| Profile | Four rounded waves, uniformly spaced 4 inches on center |
| Panel depth | 7/8 inch |
| Fastening | Concealed fastening leg and interlock; no exposed fasteners on the face |
| Gauge options | Typically 24-gauge steel; 22 gauge on request |
| Substrate | Galvalume steel (AZ50 under the paint); aluminum available on request |
| Finishes | Kynar 500 PVDF with ULTRA-Cool reflective pigments standard; SMP on request for budget work |
| Orientation | Horizontal or vertical |
| Applications | Exterior walls, storefront and office facades, accent bands, soffits, canopy fascias, modern homes and barndominiums |
| Lengths | Cut to length in our Forney shop; typically up to about 40 feet, limited by transport and handling |
| Wind and load ratings | Engineering data on request |
| Trims | Base, corner, jamb, head and transition trims fabricated in our own sheet metal shop |
Where Is the Wave 16-4 Used Around DFW?
On buildings where the wall is part of the design. That means retail and office facades, medical and professional buildings, schools, churches and modern homes. Pure agricultural buildings usually get an exposed-fastener panel instead, because it costs less and nobody is judging the screw heads.
Commercial and institutional
A 16-inch module covers a wall quickly and lines up with common stud and girt spacing. Run it horizontally across a storefront to stretch a short building, or vertically on a tall elevation to add height. It pairs well with aluminum composite panels at entries, with the Wave carrying the field and ACM handling the feature wall.
Modern homes and barndominiums
Homeowners in Rockwall, Heath and Forney use the Wave 16-4 as full cladding or as a contrast band over brick or stone. On a barndominium it dresses the living side while the shop side keeps a plainer panel. The concealed fastening is the point: a home should not show rows of screws.
Agricultural and light industrial
It shows up on office fronts and showrooms attached to shops and warehouses, where the back of the building carries a plain corrugated panel and the public face gets the Wave.
How Do We Install the Wave 16-4?
Over a flat, plumb substrate with a weather barrier behind it, with the fastening leg screwed into framing or furring, and shop-made trims closing every edge. The sequence is the same whether the panels run across or up the wall.
- Substrate: plywood or OSB sheathing over wood or metal studs, steel girts on a metal building, or masonry and concrete with anchored furring.
- Weather barrier: a mechanically fastened or self-adhered weather-resistive barrier, lapped shingle-fashion and taped at seams, before any furring goes on.
- Furring: hat channel or Z-furring, typically at 16 to 24 inches, to create a flat plane and a drainage gap behind the panels. Vertical panels need horizontal furring; horizontal panels need vertical furring.
- Fastening: screws through the concealed leg into the furring, hidden when the next panel locks on. Fastener spacing follows the engineering for your wind zone.
- Trims and flashings: base flashing, inside and outside corners, jamb and head trims, and transitions to roofing or masonry, all formed in our custom sheet metal shop in the same Kynar color.
Horizontal or vertical?
Horizontal runs are the common choice on storefronts and long, low buildings; they need a drained furring plane and careful end joints with a backer. Vertical runs shed water faster and suit tall elevations. Both are standard for this profile, and we detail each on the shop drawings.
How Does the Wave 16-4 Handle Texas Weather?
Well, as long as the gauge, finish and movement details are right. Walls take hail at a glancing angle, so a 24-gauge Wave panel with four stiffening waves rarely shows more than a cosmetic mark even in Hail Alley. We still recommend 24 gauge over 26 for any wall that faces open ground to the west or north.
Sun is the bigger enemy. Dallas summers push the UV index to 9 or 10 and bring roughly 20 days at or above 100 F in a typical year. A Kynar 500 PVDF finish resists chalk and fade far longer than silicone-modified polyester, which is why it is our standard on this panel; see Kynar 500 vs SMP.
Thermal movement matters more than most people expect. In January 2024, DFW stayed below freezing for 89 straight hours; seven months later the same wall sat in triple-digit heat. The concealed fastening leg lets each panel move slightly, and on runs beyond about 30 feet we add expansion details so the finish never buckles. Oil canning is minimal on a wave profile because the sheet has almost no flat area; the flat trims around it are where we pay attention. Read more in our oil canning guide.
Wave 16-4, Wave 12-3 or 7.2 Rib: Which Profile?
Pick the Wave 16-4 for broad walls and faster coverage, the Wave 12-3 for a tighter rhythm on small facades and accent areas, and the 7.2 Rib when you want a bolder 1.5-inch trapezoid that can also run onto the roof.
| Factor | Wave 16-4 | Wave 12-3 | 7.2 Rib |
|---|---|---|---|
| Coverage | 16 in | 12 in | Typically 36 in |
| Depth | 7/8 in | 7/8 in | 1.5 in |
| Fasteners | Concealed | Concealed | Exposed |
| Look | Soft, wide rhythm | Tighter, finer rhythm | Bold trapezoid shadows |
| Roof use | No | No | Yes |
All three sit in our metal wall panel line and come in the same Kynar colors, so a building can mix them without a color mismatch.
Lead Time, Spec Sheets and Ordering
Stock Kynar colors are typically available a few weeks after approved shop drawings; custom colors take longer. We confirm the delivery date on your written quote.
For commercial work we send a submittal package: the profile spec sheet, a color chart, the finish warranty, trim details and engineering data on request. For a home, we measure, show samples and give a written estimate backed by our transferable lifetime workmanship warranty. Either way, start with a free price quote. Our owner brings 26+ years of metal roofing and cladding experience to every wall we build.
Building a shop, barndominium or commercial structure that needs a roof as well? See commercial metal roofing in Dallas-Fort Worth; one crew handles both.
Homeowner Reviews
What Dallas-Fort Worth Homeowners Say About Architectural Metal Panels
AMP Wave 16-4 Questions
Can the Wave 16-4 be installed horizontally?
Yes. The profile is designed for horizontal and vertical use. Horizontal runs need vertical furring and a drained cavity behind the panels, which we detail on the shop drawings.
Does the Wave 16-4 show any screw heads?
Not on the field of the wall. Fasteners go through a concealed leg that the next panel covers. Only some trims, such as a base or termination trim, may use color-matched fasteners.
What gauge should I specify in Dallas-Fort Worth?
Typically 24-gauge Galvalume steel. It is about 28% thicker than 26 gauge, resists hail dents better and stays flatter on long runs. 22 gauge is available on request for walls that take abuse at ground level.
Can the Wave 16-4 be used as a roof panel?
No. It is a wall panel. For a roof with a related look, consider the 7.2 Rib or a standing seam system; we can match colors across both.
Do you provide submittal packages for architects?
Yes. Ask for the spec sheet, color chart, finish warranty, trim details and engineering data through the quote form, and we send a submittal package for your project.
What is the difference between the Wave 16-4 and a corrugated panel?
Corrugated panels use exposed washer-head screws and have a tighter, sharper profile. The Wave 16-4 hides its fasteners, has four wide rounded waves per 16-inch panel and is meant for walls where appearance matters.
Get Your Free In-Home Estimate
Tell us about your project and a Architectural Metal Panels specialist will call you back within one business day. No pressure, no obligation.
Or text a photo of your roof to (469) 569-3956
Prefer to talk now? Call (469) 569-3956. Fully Insured.
Specifying a Wave 16-4 Wall in DFW?
Send plans for a submittal package or book a free measurement for your home. Panels and trims are made in our Forney shop and installed by our own crews. Call (469) 569-3956.